silverado_ss_04 Posted January 2, 2009 Report Share Posted January 2, 2009 i just put my new pcm in from zippy and my truck wont start, anyone know how to fix this? Code: P1631 Theft Deterrent Password Incorrect Quote Link to comment Share on other sites More sharing options...
Fireman31 Posted January 2, 2009 Report Share Posted January 2, 2009 Did you perform the security relearn procedure? Quote Link to comment Share on other sites More sharing options...
Fireman31 Posted January 2, 2009 Report Share Posted January 2, 2009 from AllData......... DTC P1631 CIRCUIT DESCRIPTION The class 2 serial data circuit is used in order to communicate between the powertrain control module (PCM) and the vehicle theft deterrent (VTD) body control module (BCM) systems. When the Passlock portion of the VTD system has sensed the proper operation of the ignition switch and lock, or determined that the switch and lock have not been tampered with, the BCM transmits a password to the PCM. Fuel delivery is enabled if this password matches the password stored in the modules memory. If a component in the theft deterrent system has been replaced, the modules need to relearn the password of the new components. If the relearn procedure was not performed, this DTC will set. If a VTD failure occurs during an ignition cycle that the PCM has enabled fuel, then the BCM will enter a fail-safe mode: Fail Enable VTD System Failure with Fuel Enabled. The BCM remains in Fail Enable Mode, for the current and future ignition cycles, until the fault is corrected and a valid password is received, or until battery power is removed. If the battery is disconnected or the codes are cleared, the vehicle will lose its Fail Enable status and will not start until the fault is corrected, the 10-minute timer expires, and the PCM receives the correct fuel delivery password. DTC DESCRIPTOR This diagnostic procedure supports the following DTC: DTC P1631 Theft Deterrent Fuel Enable Signal Not Correct CONDITIONS FOR RUNNING THE DTC DTC P1626 is not active. The PCM is not in Password Learn mode. The VTD Passlock system is enabled. The fuel enable decision point has been reached, or the engine is cranking. CONDITIONS FOR SETTING THE DTC The PCM did not receive a valid password before the fuel disable decision point was reached. ACTION TAKEN WHEN THE DTC SETS The PCM stores the DTC in history after the first failure but will not illuminate the malfunction indicator lamp (MIL). The PCM records the operating conditions at the time the diagnostic fails. The PCM stores the failure information in the scan tool Freeze Frame/Failure Records. CONDITIONS FOR CLEARING THE MIL/DTC A history DTC will clear if no fault conditions have been detected for 40 warm-up cycles. A warm-up cycle occurs when the coolant temperature has risen 22°C (40°F) from the start-up coolant temperature and the engine coolant temperature (ECT) exceeds 70°C (160°F) during the same ignition cycle. Use the scan tool Clear Information function. DIAGNOSTIC AIDS IMPORTANT: Do not clear DTCs unless directed by a diagnostic procedure. Clearing DTCs will also clear valuable Freeze Frame and Failure Records data. If the PCM is replaced, the PCM must re-learn a valid password and crankshaft variation. If the BCM is replaced, the PCM must re-learn a valid password. Check for published service bulletins relating to exhibited symptoms or component operation. If the vehicle does not start, or starts and stalls: Turn OFF the ignition and wait at least 5 seconds before trying to restart. If a fault or tamper has been detected, the BCM will not forward the correct password to the PCM for a period of 10 minutes , even if the condition is corrected during that time period. This may cause a DTC P1631 to set in the PCM. This timer can be monitored in the Passlock Data parameter of the scan tool. Once the time has elapsed, the BCM will determine if the condition is still present. The PCM and BCM parameters can be monitored with a scan tool. The Passlock state and the auto learn timer can be viewed in the Passlock Data parameter of the scan tool. Inspect the following for preventing the Passlock sensor from communicating with the BCM: Passlock sensor Ignition switch assembly Passlock sensor circuitry Bent pins at the small Passlock sensor If this DTC sets along with a DTC B2960, then the problem was caused by malfunctioning Passlock components or circuitry, not the PCM. Inspect all related wiring and connections including the PCM and BCM connections. These may cause an intermittent malfunction. An intermittent may be caused by any of the following conditions: A poor connection Rubbed through wire insulation A broken wire inside the insulation Thoroughly inspect any circuitry that is suspected of causing the intermittent complaint. If a repair is necessary, Quote Link to comment Share on other sites More sharing options...
silverado_ss_04 Posted January 2, 2009 Author Report Share Posted January 2, 2009 how can i do the security relearn procedure? Quote Link to comment Share on other sites More sharing options...
silverado_ss_04 Posted January 2, 2009 Author Report Share Posted January 2, 2009 oh i think i got it, im going to try this. How to and Helpful Tips... ATTENTION: Your vehicle may not start unless this procedure is performed. GM introduced an anti-theft system in 1996 and newer vehicles. In order for your vehicle to start, you must perform the passkey relearn procedure. If your vehicle’s battery is low, it is recommended a battery charger be hooked up at this time. This Procedure will take approximately 20-30 minutes. After your PCM is installed, please perform the following. You may want to be outside your vehicle so shut the door, roll down the window. PROCEDURE: Insert key, attempt to start the vehicle and leave the key in the ON position. In some vehicles, the Battery and Security light will blink for several seconds, and then shut off. Then the Security light will then remain ON. Leave the ignition ON until the Security light goes OFF. This will take more than 5 mins. When the Security light goes OFF, turn the ignition to the OFF position. Leave ignition OFF for 20 Seconds. Attempt to start the vehicle again and leave the key in the ON position. In some vehicles, the Battery and Security light will blink for several seconds, and then shut off. Then the Security light will then remain ON. Leave the ignition ON until the Security light goes OFF. This will take more than 5 mins. Turn the ignition to the OFF position for 20 Seconds. Attempt to start the vehicle again and leave the key in the ON position. In some vehicles, the Battery and Security light will blink for several seconds, and then shut off. Then the Security light will then remain ON. Leave the ignition ON until the Security light goes OFF. This will take more than 5 mins. Once this entire procedure has been completed (three times) your vehicle will start on the fourth attempt. Note: Some vehicles perform the relearn in a different sequence. You may notice your security light, battery light and abs light will alternate. Once the security light is left out of the sequence that is considered one step. Repeat the procedure two more times and on the fourth time your vehicle will start. FAQs: - The procedure was just completed now my car is making a clicking noise when I attempt to start it. Your battery may have become too weak to crank the engine over. I performed the procedure and my vehicle still doesn't start Please repeat the procedure again. Quote Link to comment Share on other sites More sharing options...
silverado_ss_04 Posted January 3, 2009 Author Report Share Posted January 3, 2009 i got it working, thanks Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.