Search the Community
Showing results for tags 'stopping'.
Found 2 results
11-14-2019 So it’s that time again ladies and gentleman. As many of you know I made and sold the adapter brackets to mount Z06 Corvette calipers on Silverado SS trucks using Baer disks. The first batch I made was almost 9 years ago. I’ve made more smaller batches along the way. Currently I am sold out of the adapter brackets. I was not planning on making any more due to more than a few reasons. For starters, all my contacts and hookups at machine shops have either moved on or changed fields. I will no longer be able to get any discounted rates for small batches of the machine work, the raw materials, hardware or anodizing. This means I will have to do one single large batch. That means I will have to put out more than $10,000 to make a batch. That is significantly more than what i paid years ago. Now I don't have anything close to enough to sink that much money into these brackets. But I have had more than a few people recently persistently asking about purchasing brackets. So to help offset the initial cost I will be offering them to anyone that purchases them before they are finished at a discounted price. Pre-sale price Front and rear $400 Front only $250 Rear only $200 After pre-sale price Front and rear $450 Front only $275 Rear only $225 Here is a link to the How-to I wrote for anyone not familiar with this upgrade. You can also contact me at [email protected] if you are not a member here. But I would highly suggest joining so you can be part of the forum/community. There are a lot of really good guys on here with a lot of helpful knowledge. Currently the front brackets are being made. I still have a limited number of rear brackets from the last run. More rear brackets will be made shortly after the current batch of front brackets are done. FYI, this very well could be my last so get them while you can and spread the word. If you refer anyone that buys a set of brackets and they mention your name, I’ll send you a few bucks for your time. 11-19-19 12-4-19 Hope everyone had a happy Thanksgiving. So the forum went down for a bit but it’s back up. Had a few people panic. Don’t worry gentlemen. Even if the forum were to go away, you will all get tour parts. I’ve been selling these brackets for nearly a decade. Even when USPS busted open a box with two full sets and wouldn’t refund my money, I made sure the customer still got his. Anyway, front brackets are back from machine shop. Waiting on anodizing shop at this point. There is a bit of a back up due to a huge order ahead of me. They estimated late December. I’m currently working on getting rear brackets machined. Might be able to get them done before fronts are anodized, but don’t know for sure. 12-27-19 Rear brackets have been started !!! 1-10-20 Pre-sale is closed. Thank you to everyone for your patience. This forum is full of some really great people and a lot of great info. There were a couple of delays with the anodizing shop, but all the brackets sold during the pre-sale have shipped. If you missed out on the pre-sale, I still have more. Contact me [email protected] I will get back to you ASAP.
So after running the numbers, here is what I've come up with. If at least 15 people or more are willing to pay $350 up front I will make one more run, probably the last. I will post a list of names on this thread to keep track. No money will be collected initially. Just need your name for the time being. If we get enough people I will contact everyone and send invoices through Paypal. Everyone will have 2 weeks to pay. After I receive all the funds, I will move forward. If people back out after invoices have been sent I will refund everyone's money that has paid and that will be it. I cannot promise a date when they will be ready. It all depends on how busy the machine shops are when I bring them the work. But from past experience it shouldn't take more than a month or two from the time all funds are collected to the brackets and hardware arriving at your door. So if you want in on the group buy post in this thread and send me a pm with your email address so I can send the paypal invoice as soon as we get enough people. Im still working on finding better prices for raw materials and hardware but Ive had several people asking about how much will brackets be for the group by and after. So tentatively this is what I came up with but it may change. Group buy price Front and rear $350 Front only $225 Rear only $175 After group buy price Front and rear $400 Front only $250 Rear only $200 Here is a link to the How-to I wrote for anyone not familiar with this upgrade. http://www.silveradoss.com/forums/topic/64830-z06-brake-conversion/ You can also contact me at [email protected] if you are not a member here. But I would highly suggest joining so you can be part of the forum/community. There are a lot of really good guys on here with a lot of helpful knowledge. 1. bbb455- front- PAID 2. HotRodV6- front and rear 3. Downeast Johnny- front and rear- PAID 4. 121DOC- front and rear- PAID 5. Cody S- front- PAID 6. Rodrigo R- front and rear- PAID 7. Jagpreet S- front and rear- PAID 8. Steven L- front- PAID 9. Justagoose- front and rear- PAID 10. wyopoke1- front and rear 11. oldnash- front- PAID 12. toxic donkey- front and rear 13. ejb2316- front and rear- PAID 14. Robert T- front only- PAID 15. Jorge C- front and rear 16. 2drchevyss- front and rear- PAID 17. Hellfish- front and rear- PAID 18. Jared N- front and rear- PAID 19. James W- front only- PAID 20. Mitch M 2 sets front and rear- PAID 21. Douglas S front and rear- Paid 22. Christopher S 23. Trizney- front and rear- PAID 24. Zachary H- front- PAID 25. Ryan S- front and rear- PAID Ok gentleman. Looks like we have enough people if everyone follows through. I will still add people that want to be included until I place the order with the machine shop. I will give them a call this week and see what their schedule looks like. Sorry I havent been on here sooner. Ive been slammed at work doing 16 hour days. Ive felt like a zombie the last week. Hopefully things slow down. Update 6-18 Machine shop is still backed up and busy. Looks like another. Week or so. Ill update when I have more info. Update 6-20 Ok ladies and gentleman. Just put in my order for raw materials this morning. It is officially happening. In the next few days I will be sending out info to each person and then invoices. Even if youve already sent it, please send me your email again. The machine shop will start on these next week. Then off to get anodized. Should have them ready to ship by mid July. Update 7-5-16 I won't bore you with the details, but there were a few delays. Good news is that the brackets will be done today and dropped of at the plating shop tomorrow. Almost all the hardware is scheduled to arrive tomorrow. The last of it scheduled for Monday. Update 7-12-18 Brackets were dropped off on Monday. I was told they would be ready by Friday. If they are, I will begin shipping them out this Sat. Update 7-16-18 Just got off the phone with the plating shop. Brackets should be done on Wed. Update 7-22-18 Just got done boxing up a bunch of brackets. I will drop them off at the post office tomorrow. When the shipping label created, each person should get an email from Paypal with the tracking information. Depending on where you live, you should receive your package within a few days. After work everyday, I'll box up more and drop them off until the next day. Thank you everyone for your patience.