Jump to content

1981evildisco

Member
  • Posts

    142
  • Joined

  • Last visited

  • Days Won

    1

Posts posted by 1981evildisco

  1.  

    On 7/24/2019 at 7:46 AM, someotherguy said:

    The emblems for the exterior?  You won't want them used; they're too fragile and are likely to break pulling them off a truck.  In fact when I had mine painted I replaced them anyway because they were showing signs of sun damage.

    You can get the Intimidator scripts brand new if you hunt hard enough.  The door scripts are easier to find; it's the tailgate script that is a little bit narrower so that it doesn't crowd out the SS emblem.  The non-original copies of the scripts that are all over ebay etc. are just vinyl puffy stickers and are not correct to originals whatsoever so please skip those.  I got the tailgate script from online Chevy dealer IAMGMPARTS if I recall; will edit back with the part #'s when I dig through my file in a little bit.

    Of course the SS emblems are the same exact ones used on the regular SS truck.

    The dash insert...you gonna have to get it from someone willing to part with one.  I know there's probably someone here that has one though.

    EDIT - part #'s

    Intimidator scripts for doors - 88980874 - best price I found 3 years back was $153/ea

    Intimidator script for tailgate - 88980875 - same deal 3 years ago best price I found was $157 - this is the smaller one correct for the tailgate.

    SS emblems - same for doors and tailgate - 15178666 - around $80/ea :(

    If you're restoring though you're laying out good money for paint and bodywork, may as well only go with brand new emblems.  When you compare 'em to the old ones you won't regret it.  Yes it's over $700 for 6 emblems total, which in reality, is only about 10% of what high quality paint/body is gonna cost.

    Richard

    where did you find these???? I need to know!!!

  2. Bought my ISS with 108k

     

    Currently with 211k

     

    Ive routinely changed all fluids(replaced Trans Servos on the back of the pan when I broke them accidentally)

     

    Replaced the water pump with an ACDelco Replacement(did T-stat while in there)@210k

     

    It does need the driver side seat foam/cover/seat heater element replaced.(I believe the previous owner was a big dude)

     

    Other than that it has not required any unscheduled maintenance.

  3. In order to prevent buttpain as I suffered doing the aforementioned maintenance, Im going to set up a simple step by step guide for this service. This is by no mean all inclusive, nor will I accept any liability for damages/injury incurred as a result of this service. This guide is based on the best available information.

     

    Im this write up I will be strongly recommending the replacement of the A and B Transmission control solenoids.

    Reasons for this: You are already in there, they improve shifting, are cheap, and easily replaced.

     

    I am assuming you have the TCI Deep Cast Trans Pan (stock will be similar and easier, but we arent here for stock or easy)

     

    Quickly look underneath the Trans to verify you have the deep pan. If there is a step down by the exhaust midpipes, you have the deep pan if not you dont.

     

    If your pan has no drain plug. GET AN AFTERMARKET DRAIN PAN. Reason: the pan without a drain plug makes a massive mess and makes an easy task irritating.

     

    The TCI deep pan is awesome, very sturdy and made in USA. Had mine for a couple years no issues, looks and works great.

     

    Tools:

     

    T30 Torx bit(preferably on a 3/8ths socket)

    15mm deepwell/Shallow well socket

    3/8ths ratchet

    3 and 8 extension

    4 post lift or ramps(if using ramps ensure you have the parking brake and a chock block for the rear wheels)

    A jack (screw type if using a lift)

    Patience

    A breaker bar

    Torque wrench

    RTV

    Magnetic small parts holder or cup

    Assistant if possible

    Drain pan

     

    Parts:

     

    6 Qts Castrol Dextron VI Synthetic oil(call dealer with vin to ensure which Dextron Spec fluid your year trans requires)

     

    SL1007 Delphi Or AcDelco transmission Control Solenoid

    24208576 AcDelco Deep Transmission Filter.

    (Double check part numbers)

     

     

    Step 1.

     

    Get the truck on the lift and raised so that the transmission is at eye height.

    - if using ramps Id suggest using 4 so that the whole truck is raised.

    (Use chock blocks and parking brakes regardless)

     

    Take keys out and put them somewhere secure

     

    Get hood completely open, and pull dipstick out and wipe it clean.

    Place dipstick on the air filter housing.

     

    Step 2

     

    Loosen the rear trans mount nut (inside crossmember under output shaft housing)

    (15mm socket)

     

    Step 3

    Remove the (2) 15mm nuts holding the exhaust midpipes to the mount on the passenger side of the truck immediately next to the rear trans mount bolt.

    Doing this will facilitate the removal of the pan.

     

    Step 4

    Remove the (2) Torx bolts from the bracket holding the drive selector cable on.

    Move the bracket to the side. Do not attempt to remove the cable from the bracket, this is unnecessary.

     

    Step 5

     

    Place the drip pan underneath the Trans. Loosen and remove the drain plug.

     

    If you are working with the stock pan, may the maintenance gods have mercy on your soul. But in all seriousness make sure you have a steady hand and try not to get ATF everywhere.

     

    Step 6

     

    Place the jack underneath the output shaft housing. Jack up until you see the fuel lines get on the body, you may have to squish them up there a little bit but be careful not to break the plastic mounts.

     

    Step 7

     

    Start loosening/removing the capscrews holding the pan on, there are 16.

     

    When you get to the last one be careful the pan may want to fall on you.

     

    If it isnt, get the pan unstuck so it is held only in place by the exhaust/ accumulator.

     

    Step 7

     

    Remove the filter, this is hard to explain, but when you see it it will come to you.

     

    The filter is located to the front of the pan, towards the middle.

     

    Step 8

     

    Having your faithful assistant pulling down on the exhaust that is in the way, pull out the pan.

     

    Step 8

     

    Remove the Trans Pan, this is a pain. Use the patience from the tool list.

     

    Step 9 (if replacing the Trans Solenoid)

     

    Take a picture of the valve body on your phone.

     

    Find the solenoid(driver side rear of the valve body)

     

    Replace the one closest to the drivers side first(this one is spring loaded) keep your thumb on the back of it while taking the screwdriver and prying off the clip.

     

    Replace using opposite procedure.

     

    The Solenoid closest to the passenger side B is not spring loaded.

     

    While replacing both of them ensure you put the clip in the same spot you found it and ensure the solenoid bottoms out completely.

     

    Check valve body against your original picture.

     

    Step 10

     

    Reassemble in reverse order as disassembly.

     

    Step 11

     

    Recheck all torque specs, and ensure you do not have any spare hardware.

     

    Step 12

     

    Fill trans with 5 qts. Check dipstick.

    Go for a test drive, get fluid up to operating temp. Recheck dipstick, ensure you check it while in park with engine idling.

     

    Thats all there is to it.

  4. I was driving on my way in for an overtime graveyard shift tonight and I noticed that my tachometer was misbehaving. It would read an increase in RPM as normal, but would not fall when engine RPM fell. Needless to say now my Tach is pinned passed 6K. Has anyone seen this before? Is it as simple as disassembling the dash and manually pushing the needle back down to 0? If I reset it manually I am afraid it will just pin out again. Anyone know what would cause this and how to fix it permanently?e63eb18e69e9c9e16a2e2a252ff93a28.jpg

     

    Sent from my STV100-1 using Tapatalk

    send it off to GMGaugeGuy

×
×
  • Create New...