Thing1

Nice truck, sits just right . Welcome to the site!

Man that truck looks so good with that drop and wheels .

Happy late birthday as well!

Any idea how much this would cost to ship to Texas? I'm almost scared to ask ... Lol.

I will be on the lookout from the Denton TX area, will let you know if I see anything!!! Hope it makes it back home safely, always kills me to see these trucks get stolen like they do.

Are you interested in shipping them to Texas?

How much for a set of cladding? Might be needing it for the single cab soon.

They look wicked on that truck! Wish I could find me some reps cheap haha.

Looks sick! Wish I could find one of those covers.

After finishing the dimmer switch and cluster in blue, I figured I could tackle the manual AC controls as well. As soon as I got all the LEDs in, I ran to plug it into the truck and got this. The two bottom on the driver side weren't working and the bottom on the passenger side wasn't either. Thinking maybe I screwed something up on the bottom of the board (Such as pos and negative touching on the led or something stupid), I took it out of its little plastic case still plugged in. The first red square shows the positive and negative, they were a little close so I moved it a hair with my finger and the circuit board started smoking for a sec (Believe I just fried the LED, as it was the led for the passenger temp control and it immediately went out afterwards). After this happened and this LED went out, all of the LEDs on the driver side went out leaving only the two on the passenger side knob to adjust the positioning (blow to feet, face, etc) still on. I then noticed this burnt mark shown in the second square. Here is the front of the circuit board, all of the positives and negatives should be in the right holes and nothing looks damaged as far as I know... Hopefully you guys can help me out and let me know what I can do to fix this, desperate at this point! Been working on this since midnight and its almost 5 AM lol. Thank you very much.

I'm on the hunt for a set of nice 22" replica wheels in Texas. Would like to find someone close by Lubbock TX (Willing to travel a little) who is looking for a stock set of OEM silvers wanting to get rid of the 22"s so it would be a simple trade off. Depending on the situation (New tires, etc) I may be willing to throw in some money on top of the stock 20"s. Lemme know what you got!

Could always go back with a factory bumper, may be cheaper than getting a bser rollpan. That's gonna be the only rollpan that'll look right with the cladding.

I was searching for some with a 180 degree viewing angle and don't think they sell them off that site but I believe I found the 360 degree ones you were talking about. I plan on doing blue, did your cluster turn out looking good with the 360 degree bulbs?- edit - These are what you used right? Thanks again man. http://www.superbrightleds.com/moreinfo/through-hole/5mm-blue-led-360-degree-viewing-angle-800-millilumens/343/1290/

I checked that superbrightled site and cannot find a 3mm 180 degree bulb anywhere on there, anyone else have a hard time finding them?

I think its time to tackle the LED swap and I was just wondering where you guys would recommend ordering LEDs for the cluster and the AC controls? I'm not sure if it would matter or not but I'd hate to order some cheap ones and they burn out lmao. Thanks!

Got stock silver 20's near Lubbock Tx if you are interested in a trade as well. Lol. Wrapped in 285/50/20 with lots of life left.

I say 6.0 Swap over the supercharger for sure. It's like what shawnss said, when you want more power down the road you will be wishing you went bigger and didn't mess with the 4.8. Or find you a good LS3, I look around here and there for my single cab but haven't ran across a good deal on one yet .

This picture off there is the best thing I've seen all day

Those look sick... Who made such a bright daytime running light?

Haha awesome, your truck sits so perfect. Pictures turned out pretty sweet too.

I believe I've read somewhere where someone didn't actually use the OEM brackets to hold the cladding on the single cab and made some homemade ones instead. I was just wondering if any of you had a design or an opinion on the OEM vs homemade ones, as I am thinking about buying this set of cladding that doesn't include brackets :/. Also, does anyone have an idea how to mount this stuff where it won't blow off driving down the street without drilling holes in every panel of my truck? Thanks!

Love that bedcover and tailgate. Truck looks awesome!

Texting you about the cladding.

Very nice looking truck, they just need to get cladding if they keep that back bumper lol. Good price as well.

Truck looks good man!